DALI 100W LED Power Supply 24V DT8 4.2A For Tunable White LED Spot and Strip

Feature

TILLUME DALI Tunable White LED Power Supply combine traditional power supply with DALI actuator function together, not only provide more flexibility in smart lighting control, but also improve driver, acutuator and luminaries compatibility.

Meanwhile, TILLUME Driver PWM Frequency is more than 3.6KHZ, which provide soft dimming and flicker-free at any brightness, meets the new requirements of ErP certification.

In addition, The control gear supports DALI-2 DT8 and CCT control, which is suitable for tunable white luminaries. It operates on a wide input voltage of 100-265V AC and 2 channels of constant voltage output with safe isoloation to mains and DALI, which offers both versatility and safety for the user.

IP65 protection grade, which is friendly to install in bathroom or kitchen.

Technical Data

Output:

DC Voltage: 24V
Voltage Adjust Range: 23-27.3V
Rated Current: 4.2A
Rated Power: 100W
Ripple& Noise (max.): 150mVp-p
Voltage Tolerance: ±3.0%
Line Regulation: ±0.5%
Load Regulation: ±1.5%
Setup, Rise Time: 500ms, 80ms 115VAC / 230VAC
Hold Up Time（Typ.): 16ms/230VAC 16ms/115VAC

Input:

Voltage Range: 100 ~ 265VAC
Frequency Range: 47 ~ 63Hz
Power Factor: PF≧0.98/115VAC, PF≧0.96/230VAC @Full load
Total Harmonic Distortion: THD< 20%(@load=100%/115VC,230VAC)
Efficiency(Typ.): >90%
AC Current: 0.95A / 115VAC 0.5A / 230VAC
Inrush Current(Typ.): COLD START 60A(twidth=550μs measured at 50% Ipeak) at 230VAC; Per NEMA 410
Leakage Current: <0.25mA / 264VAC
No load power consumption: <0.15W

Controller Interface:

DALI Dimming Port.: Voltage range: DC9.5-22.5V, typical 16V, interface current consumption: 1.8mA
Dimming Range: 1-100%
Dimming Driver Mode: PWM

Protection:

Over Current: 110~ 120%  Rated OCP 5A / Hiccup mode recovers automatically after the fault condition is removed
Short Circuit: Hiccup mode, recovers automatically after the fault condition is removed
Over Voltage: 28 ~ 29.5V Shut down and latch off o/p voltage, re-power on to recover
Over Temperature: Shut down o/p voltage, re-power on to recover

Environment:

Working Temp.: Tcase=-40 ~ +40℃
Max. Case Temp.: Tcase=+85℃
Working Humidity: 20 ~ 95% RH non-condensing
Storage Temp., Humidity: -40 ~ +80℃, 10 ~ 95% RH
Temp. Coefficient: ±0.03%/℃ (0 ~ 50℃)

Safety & EMC:

Safety Standards: EN61347-1, BS EN/EN61347-2-13 independent, EN62384, GB19510.1,GB19510.14,EAC TP TC 004,IP67 approved; Design refer to EN60335-1
Withstand Voltage: I/P-O/P:3.75KVAC
Isolation Resistance: I/P-O/P:100M Ohms / 500VDC / 25℃/ 70% RH
EMC Immunity: Compliance to BS EN/EN61000-4-2,3,4,5,6,8,11; BS EN/EN61547, light industry level (surge immunity Line-Line 2KV); EAC TP TC 020
DALI-2: IEC 62386-101(DALI-2), IEC 62386-102(DALI-2), IEC 62386-207(DALI-2), IEC 62386-209(DALI-2)

Others:

Dimension: 226*67*40mm (L*W*H)
Packing: 0.77Kg