TILLUMETILLUMETILLUME
-17%Sold out

LED Transformer 24V 90W | Constant Voltage 3.75 A Non-dim

Item Code: / Series:

$35.00 $29.00

Free Shipping

-Constant VoItage Output
-PIastic housing with CIass II design
-BuiIt- in active PFC function
-No Ioad power consumption <0 . 15W
-Protections:Short circuit/Over load/Over voltage
-Fully encapsulated with IP67 level
-Fully isolated plastic case
-Class 2 power unit -Suitable for LED lighting and moving sign applications
-l00% full load burn in test
-Low cost high reliability
-5 years warranty

Notify me when this product is available:

Availability : In StockIn StockOut of stock

LED Driver 24V 90W 3.75A For LED Spot and Strip

Feature

TILLUME transformer integrates a switching mode power factor correction (TM PFC) controller and a quasi- resonant controller (QR) controller. PFC controllers provide a cost-effective solution for optimizing power factor.  QR controllers have higher efficiency and lower electromagnetic interference compared to traditional PWM systems,.

TIECO transformer provides advanced integration and high performance than conventional  PFC/PWM system. The built-in TM PFC controller optimizes power conversion efficiency by reduced system costs. The intelligent PFC switch on and off, zero current detection, and frequency limiting mechanisms can achieve better efficiency under any load condition.

TIECO LED driver has many built-in green features to optimize power conversion efficiency. 

This LED transformer also integrates multiple protection functions, such as X-CAP discharge, break protection, unde voltage lockout, PFC and QR level cycle by cycle current limiting (OCP), PFC and Q R level output over voltage protection (OVP), PFC and Q R level open loop protection (OLP). Therefore, it can protect the system from damage caused by occasional failures.

Technical Data

Output:

DC Voltage: 24V
Rated Current: 3.75A
Rated Power: 90W
Ripple& Noise (max.) : 150mVp-p
Voltage Tolerance: ±3.0%
Line Regulation: ±0.5%
Load Regulation: ±0.5%
Setup, Rise Time: 500ms, 80ms 115VAC / 230VAC
Hold Up Time(Typ.): 16ms/230VAC 16ms/115VAC

Input:

Voltage Range: 100 ~ 265VAC
Frequency Range: 47 ~ 63Hz
Power Factor: PF≧0.98/115VAC, PF≧0.96/230VAC, PF≧0.94/277VAC@full load
Total Harmonic Distortion: THD< 20%(@load≧60%/115VC,230VAC;@load≧75%/277VAC)
Efficiency(Typ.): 91%
AC Current: 0.95A / 115VAC 0.5A / 230VAC 0.4A / 277VAC
Inrush Current(Typ.): COLD START 60A(twidth=550μs measured at 50% Ipeak) at 230VAC; Per NEMA 410
Max. No. of PSUs on 16A Circuit breaker: 3 units (circuit breaker of type B) / 6 units (circuit breaker of type C) at 230VAC
Leakage Current: <0.25mA / 277VAC
No load power consumption: <0.15W

Protection:

Over Current: 95 ~ 108%
Short Circuit: Hiccup mode, recovers automatically after fault condition is removed
Over Voltage: 28 ~ 34V Shut down and latch off o/p voltage, re-power on to recover
Over Temperature: Shut down o/p voltage, re-power on to recover

Environment:

Working Temp.: Tcase=-40 ~ +85℃
Max. Case Temp.: Tcase=+85℃
Working Humidity: 20 ~ 95% RH non-condensing
Storage Temp., Humidity: -40 ~ +80℃, 10 ~ 95% RH
Temp. Coefficient: ±0.03%/℃ (0 ~ 50℃)
Vibration: 10 ~ 500Hz, 5G 12min./1cycle, period for 72min. each along X, Y, Z axes

Safety & EMC:

Safety Standards: UL8750, CSA C22.2 No. 250.13-12, ENEC BS EN/EN61347-1, BS EN/EN61347-2-13 independent, BS EN/EN62384, GB19510.1,GB19510.14,EAC TP TC 004,IP67 approved; Design refer to BS EN/EN60335-1
Withstand Voltage: I/P-O/P:3.75KVAC
Isolation Resistance: I/P-O/P:100M Ohms / 500VDC / 25℃/ 70% RH
EMC Emission: Compliance to BS EN/EN55015, BS EN/EN61000-3-2 Class C (@load≧60%) ; BS EN/EN61000-3-3; GB17743 and GB17625.1,EAC TP TC 020
EMC Immunity: Compliance to BS EN/EN61000-4-2,3,4,5,6,8,11; BS EN/EN61547, light industry level (surge immunity Line-Line 2KV); EAC TP TC 020

Others:

MTBF: 2749.4K hrs min. Telcordia SR-332 (Bellcore) ; 292.8Khrs min. MIL-HDBK-217F (25℃)
Dimension: 171*63*37.5mm (L*W*H)
Packing:0.77Kg

Note:

1. AII parameters NOT speciaIIy mentioned are measured at 230VAC input, rated current and 25C of ambient temperature.
2. RippIe & noise are measured at 20MHz of bandwidth by using a 12" twisted pair-wire terminated with a 0.1uf & 47uf paraIIeI capacitor.
3. ToIerance : incIudes set up toIerance, Iine reguIation and Ioad reguIation.
4. De-rating may be needed under Iow input voItages. 
5. Length of set up time is measured at first coId start. Turning ON/OFF the driver may Iead to increase of the set up time.
6. The driver is considered as a component that wiII be operated in combination with finaI equipment. Since EMC performance wiII be affected by the compIete instaIIation, the finaI equipment manufacturers must re-quaIify EMC Directive on the compIete instaIIation again.
7. This series meets the typicaI Iife expectancy of >50,000 hours of operation when Tcase, particuIarIy tc point (or TMP, per DLC), iS about 75C or Iess.
8. Warranty: 5 Years
9. The ambient temperature derating of 3.5C/1000m with fanIess modeIs and of 5C/1000m with fan modeIs for operating aItitude higher than 2000m(6500ft).

Here at TILLUME LEDs, we try to make LED lighting easy to understand for our customers. Read below to understand the terminology used on this website and learn about LEDs and lighting science

General Lighting parameters

What are lumens (lm)?

Lumen is the measurement value of brightness. It said the power of light which can be seen by the eye. In fact, light is an electromagnetic wave, In common the frequency of electromagnetic waves that the average human eye can perceive is 380~750THz, and the wavelength is between 780~380nm. So we can say the total watt of light in 380nm-780nm is equal to the lumen

Lighting spectrum

 

Because incandescent lighting have the same energy conversion efficiency by different manufacturers, we are all accustomed to using watts to measure the brightness of a light. That is no problem with incandescent lighting. But it is not suitable for LED. Different manufacturers using different technology and quality level, the energy conversion efficiency will be a big difference, low quality may be 60-70lm/w, and the high quality will be 100-120lm/w for the same lamp. So we have to use lumen. Lumen is the most important parameter when choosing the LED light you need. Comparing lumen output between different products will help you to buy the right LED lamp at a reasonable price.

What is AC?

This is Alternating Current. This is the electricity that is used in most spaces. Generally, there have to 2 kinds of voltage in different countries all over the world. One is 220-240V, and the other is 110-130V. The value of voltage we said is a valid value the voltage value is different each time. It looks the same as a sine wave.

alternating current sine wave photo

From the picture, we can know the highest voltage is 311V, and 220V is near the avg value(you can understand it as simple). In developed countries, the voltage is stable. But in some developing countries, it usually is not stable due to weak basic power facilities. It may be a higher voltage or lower voltage than the rated voltage.

What are DC and safety voltage?

This is Direct Current. The current always moves in the same direction. So when the device asks for direct current, we need to connect wires as positive and negative electrodes. Safe voltage refers to the voltage that will not cause direct death or disability. The industry stipulates that the safe voltage is not higher than 36V, and the continuous contact safe voltage is 24V.

What is a Watt?

One watt is equivalent to one joule per second, and it's a measure of power consumption that your power company uses to calculate how much energy you're consuming. In the LED era, power cannot be used as a parameter to evaluate whether the light bulb is bright enough, because the better the LED, the more lumens can be emitted with less power.

What is luminous efficacy?

It is the result of dividing lumen by power. The higher the value, the higher the energy conversion efficiency. The figure below shows the new Erp's regulations on energy efficiency labels. We can see that the higher the light efficiency, the more energy saving

You can check the New Erp labeling regulations

What is CRI and why is it important?

CRI is an acronym for Color Rendering Index, when we want to know how colors look under a sunlight source, CRI is an important parameter. The higher the CRI value, the closer the color of the object being illuminated is to its true color. CRI is measured from 0 to 100. CRI80+ is the industry standard for most applications while CRI90+ is a premium level that can show your home, clothing, and furnishing look best.

cri of LED

What is color temperature?

Color temperature is a unit of measurement that expresses the color components contained in light, we also call it CCT as an abbreviation. The concept is based on a fictional black object that emits light of different colors when heated to different temperatures, and the object appears in different colors. Just like when you heat a block of iron, it first turns red, then yellow, and finally white. And it is measured in Kelvins(K).
LED lights fall in a spectrum between 2000K and 6500K. 2200K looks like a Candlelight, 2850K is the same as a standard Incandescent lamp, and 6500K is nearly the color of the noon sky.
Wider CCT adjust range in TILLUME

What is Beam Angle?

The angle formed from the main axis with the strongest light source intensity to the 50% position of the luminous intensity on both sides is the so-called beam angle.

beam angle of LED spot

For the same light source, if the beam angle is larger, the central light intensity will be smaller, and the light spot will be softer. If the beam angle is smaller, the central light spot will be stronger and the light spot will be clearer.

 

Professional lighting knowledge

What is the difference between CIE and TM-30 standards?

The CIE is a European Standard that evaluates the color rendering of the light source as Ra or CRI. TM-30 is the US method for Evaluating Light Source Color Rendition as Rf and Rg.
  • TM-30 using 99 sample colors to evaluate the color rendering parameters of light sources.
  • CIE using 8 or 15 sample colors to evaluate the color rendering performance.
So TM-30 Standard is higher than CIE. If you want to buy premium lighting, we need to use TM-30 to check.
CRI and TM-30 are different

Besides CRI, you also need to care about Rg and Rf

Rf is Color Fidelity Index, it is from 0 to 100, it is similar to CRI, but it uses 99 sample colors. Rf =100 is the maximum value, which means that there is no color difference with the color under the natural light source, and the color effect is realistic. 

The color saturation Rg is used to characterize the color gamut index GAI (Gamut Area Index) of the light source, that is, the saturation degree of each standard color compared with the reference light source under the illumination of the test light source. The index of 100 represents the best saturation.

    • Rg = 100, which means that the saturation of the light source is the same as that of natural light, and the color saturation is moderate
    • Rg>100, which means that the light source can increase the saturation of the color, and the object looks more vivid and vibrant
    • Rg<100, which means that the saturation of the color will be reduced under the test light source, the color saturation will be insufficient, and the object will become dull and dull

Why do my lights have different colors, What is SDCM?

SDCM is a unit of measurement for color tolerance. It is also an abbreviation for Standard Deviation of Color Matching.

Color tolerance refers to the difference between the formula calculated by the computer and the target standard. It is calculated under a single lighting source. The smaller the value, the higher the accuracy.

Relevant standards require that SDCM should be less than 6, and usually, high-quality light sources can reach 3 and below

Different SDCM Effect

 

What is Binning?

Simply put, binning is the process of grouping LEDs during production so that they matched with LEDs of the same color sector. For example, all 2700K chips are ‘binned’ together and are separated from chips that have a higher/lower color temperature. Learn more about Binning here.

If LED are binned together with a very narrow CCT range, Lighting color consistency will be good

What is the voltage drop?

When installing LED strips or other DC-powered fixtures, be sure to consider the effect of "voltage drop". In a DC circuit, the voltage drops gradually as it passes through a length of wire, and the longer the line, the greater the voltage drop. Therefore, for each meter of wire, the available voltage decreases gradually along the length of the wire. This is also why one end of the strip light is brighter than the other.

What is peak current?

Someone also called it Inrush Current

The peak current generally refers to the transient high-amplitude current signal that appears in the power supply line or electronic circuit. It may be generated when the power supply is started or turned off, or it may be the interference caused by other equipment. Electrical appliances and electronic equipment must take various measures to suppress the peak current and make the equipment work stably.

Sunday,Monday,Tuesday,Wednesday,Thursday,Friday,Saturday
January,February,March,April,May,June,July,August,September,October,November,December
Not enough items available. Only [max] left.
Shopping cart

Your cart is empty.

Return To Shop

Add Order Note Edit Order Note
Estimate Shipping
Add A Coupon

Estimate Shipping

Add A Coupon

Coupon code will work on checkout page